Testo 410i Bluetooth vane anemometer with app
- SKU: 0560 1410
- VENDOR: TESTO
Couldn't load pickup availability
Safe and secure payments:
Informazioni di prodotto e di utilizzo
The testo 410i Bluetooth vane anemometer from the Smart Probes range, used with a smartphone or tablet, measures air velocity, volume flow and air temperature at vents.
Key features
- For balancing the air volume flow of a ventilation system
- Simple setup of the duct cross-section for determining the volume flow
- Analysis, storage and sending of measured values with the testo Smart app
- Compact and easy to carry
Description
The testo 410i Bluetooth vane anemometer is part of the Smart Probes range. Combined with a smartphone or tablet, it is suitable for measuring air velocity, volume flow and temperature at vents and for balancing the air flow of a ventilation system. The app is used to read the measured values, set up volume flow measurements and determine mean values over points or over time; when balancing a system, the volume flows of different vents can be compared. Measurement reports can be sent as PDF or Excel files.
Typical applications
- Balancing the air volume flow in ventilation systems
- Air velocity and temperature at vents
- Comparing the volume flows of several vents
Technical data
| Temperature - NTC | |
| Measuring range | -20 to +60 °C |
| Accuracy | ±0.5 °C |
| Resolution | 0.1 °C |
| Velocity - vane | |
| Measuring range | 0.4 to 30 m/s |
| Accuracy | ±(0.2 m/s + 2 % of reading) (0.4 to 20 m/s) |
| Resolution | 0.1 m/s |
| General technical data | |
| Weight | 117.8 g |
| Dimensions | 154 x 43 x 21 mm |
| Operating temperature | -20 to +50 °C |
| Housing material | Plastic |
| System requirements | requires iOS 13.0 or later; requires Android 8.0 or later; requires mobile end device with Bluetooth 4.2 |
| Product colour | black/orange |
| Battery life | 130 ore |
| Battery type | 3 x AAA batteries |
| Vane diameter | 30 mm |
| Storage temperature | -20 to +60 °C |
| Product code | 0560 1410 |
Supplied with
- testo 410i, Bluetooth vane anemometer with app, incl. protective cap, batteries and calibration certificate
Documentation
Selection guide: which anemometer
The choice depends on the measuring point. Vane anemometers are suited to vents, grilles and medium-to-high flows: the small vane for ducts and narrow vents, the 100 mm vane for grilles and diffusers, where it averages the velocity over a larger surface. Hot-wire anemometers are the choice for low velocities and for measurements inside ducts. Multifunction instruments with interchangeable probes are needed when temperature, humidity or other environmental parameters are measured in addition to air velocity.
Check the velocity range and accuracy in the Technical data against the values you need to measure.
If in doubt, contact us with your application, measuring range and required accuracy: our technical support will recommend the right model and accessories.
Integration and programming
The instrument is ready to use and requires no programming. To calculate the flow rate, simply set the cross-section of the duct or vent. Models with Bluetooth connect to the testo Smart app on a smartphone or tablet: values can be read remotely, averages are calculated by points or over time, and the measurement report is exported to PDF or Excel for acceptance test documentation.
Calibration and repair
For acceptance measurements and under ISO 9001 we recommend periodic calibration (normally annual) in a wind tunnel with certificate; on request we supply the instrument already with an ISO or ACCREDIA calibration certificate. Protect the vane or sensor with the cap after use and do not expose them to dust and impacts.
Service: RODER S.r.l. – INNOVACHECK division handles, in Italy, calibration with certificate (including ACCREDIA through partner laboratories), periodic verification and the management of repairs of Testo instruments at the manufacturer's service centre. Contact us with the model and serial number.

