GT282 pneumatic probes TESA, ± 2 mm, plunger travel 10.3 mm, radial cable
This product is priced individually. Fill in the form to receive a dedicated quote.
Informazioni di prodotto e di utilizzo
TESA GT 282 inductive probe, measuring range ± 2 mm.
Description
GT282 pneumatic probe, ± 2 mm, force = 1 N, radial cable.
Probe:
- Pneumatic probe
- Probe with long plunger lift
- Measuring plunger mounted on a ball bearing
- Guide ensuring low sensitivity to radial forces acting on the measuring plunger
- Guide separate from the mounting shank, so that the movement of the measuring plunger is not adversely affected if the probe is clamped incorrectly
- Ø 8 mm mounting shank that can be clamped along its entire length
- Guides highly protected against the ingress of liquids (oils) or solids (dust) by a protective bellows
Measurement:
- Probes intended for use with devices that integrate fully or semi-automated measuring sequences
- The measuring plunger is lifted by the force of the spring
- Probe brought into the measuring position by pneumatic actuation (depending on the model)
- Contact points can be replaced or changed
- Measuring force adjustable by changing the spring (depending on the model)
TESA GT 282 inductive probe, compatible with the M4P-3 4-input interface with analogue output.
Technical data. Measuring range ± 2 mm; nominal output signal with M4P-3 100 mV for a travel of 100 µm from 0 with 1 V/mm gain.
Key features
- Pneumatic probe
- Probe with long plunger lift
- Measuring plunger mounted on a ball bearing
- Contact points can be replaced or changed
- Measuring range ± 2 mm
- Repeatability limit 0.05 µm
Technical data
| Series | GT282 |
| Measuring range [mm] | ± 2 |
| Repeatability limit [µm] | 0.05 |
| Hysteresis [µm] | 0.05 |
| Maximum permissible linearity error [µm] | 0.2 + 3 x (L x L x L) |
| Plunger lift | Advance: pressure, lift: spring |
| Cable orientation | Radial |
| Sensitivity [mV/V/mm] | 73.75 |
| Cable length [m] | 2 |
| Standard | DIN 32876 |
| Material | Mounting shank: nickel-plated; Measuring plunger: hardened steel; Protective bellows: Viton®; Ball contact point: carbide |
| Dimensions | Mounting shank: Ø 8 mm; Contact thread: M2.5; Ball contact point: Ø 3 mm; Cable: 2 m; Connector: 5p DIN 45322 |
| Mass | Moving mass: 8 g |
| Hysteresis | 0.05 µm |
| Coefficient of linear expansion | 0.15 µm/°C |
| Repeatability | 0.05 µm |
| Measuring range | ± 2 mm |
| Plunger travel | 10.3 mm |
| Operating temperature | 20 °C ± 0.5 |
| Sensitivity | 73.75 mV/V/mm |
| Maximum permissible linearity error | L in mm; 0.2 + 3 x (L x L x L) µm |
Models and variants
| TESA code | Item | Protection rating | Measuring force [N] | Nominal pressure [bar] | Maximum pressure [bar] |
|---|---|---|---|---|---|
| 03230053 | Pneumatic GTL 282 probe with long plunger lift / Nominal measuring force 1.0 N | IP65 | 1 | 1.1 | 1.5 |
| 03290141 | Set of 10 GT 282 probes | IP65 | 1 | 1.1 | 1.5 |
| 03290173 | Set of 10 GT 282-A probes | IP50 | 0.85 | 1 | 6 |
| 03230069 | Pneumatic GTL 282-A probe with long plunger lift / Nominal measuring force 0.85 N | IP50 | 0.85 | 1 | 6 |
Supplied with
Probe · Clamping bush · Adjusting key · Inspection report · Instruction manual · Declaration of conformity
Documentation
- Document: 15-08-21-catalog extract-dc lever probe lever probe axial probes
- Document: 15-08-21-catalog extract-numerical index index 3 cat gen en p481
- Document: 15-08-21-catalog extract-pneumatic gt282 probes 2 mm 10 3 mm bolt
- Data sheet / dimensions: 03200390a
- Data sheet / dimensions: 03200432
Manufacturer's official page: tesatechnology.com
Price and availability
Products without a listed price are offered with a configuration defined together with our technical support: contact us for a quote stating the model, quantity and application.
Selection guide: TESA GT282 pneumatic probes, ± 2 mm, plunger travel 10.3 mm, radial cable
TESA GT 282 inductive probe, measuring range ± 2 mm.
TESA inductive probes (half-bridge system) are selected according to measuring range (± 1, ± 2, ± 5 mm), measuring force (from 0.16 to 4 N depending on the material and finish of the workpiece), cable exit (axial or radial, depending on the space available in the fixture) and plunger lift (manual or pneumatic, GTx2 and GTLx2 versions). The GTL versions are linearised for maximum accuracy over the whole range; the DC versions have a voltage analogue output for PLCs; the USB versions connect directly to a PC without a display unit; the FMS parallel-guided probes are for measurements with constant force and interchangeable probes; lever probes are for hard-to-reach points. The probe must be paired with a display unit (TWIN, TT100) or an interface (M4P-3, TESA-MODUL) and with suitable contact points.
If in doubt, contact us: our technical support will advise you on the right model, measuring force, contact points and display unit for your application.
Integration and programming
The probe is fixed by its Ø 8 mm h6 shank in the holder or measuring fixture and connected to the display unit or interface via the 5-pin DIN connector (or USB for the USB versions, voltage output for the DC versions). Zeroing, presets, tolerances and formulas between several probes are set on the display unit; with M4P-3 and TESA-MODUL the signals go to PLCs, acquisition boards and SPC software. Probes with pneumatic plunger lift require the pneumatic accessories (electropneumatic pump, fittings) listed among the accessories.
Calibration and repair
Every TESA probe is supplied with an inspection report and a declaration of conformity. Periodic verification on gauge blocks or setting standards is recommended and, for quality systems, calibration with a traceable certificate; replace worn contact points and damaged bellows. After impacts or unstable readings the probe should be sent in for service.
Service: RODER S.r.l. – INNOVACHECK division handles verification, calibration with certificate and repairs of TESA probes and display units in Italy. Contact us stating the model and serial number.