TESA GT 622 DC pneumatic probe 5 mm 2 N
This product is priced individually. Fill in the form to receive a dedicated quote.
Informazioni di prodotto e di utilizzo
TESA GT622 DC probe, pneumatic, ± 5 mm, force = 2 N, radial cable – measuring range ± 5 mm; repeatability limit 0.1 µm; hysteresis 0.15 µm.
Description
TESA GT622 DC probe, pneumatic, ± 5 mm, force = 2 N, radial cable, manufactured by TESA Technology (Switzerland), «GT622 DC pneumatic probe, ± 5 mm, plunger travel 10.3 mm, radial cable» family.
Technical data: Measuring range [mm]: ± 5; Repeatability limit [µm]: 0.1; Hysteresis [µm]: 0.15; Measuring force [N]: 2; Protection rating: IP65; Mass [g]: 173; Plunger lift: Advance: pressure, lift: spring; Output voltage [V]: ± 5; Sensitivity [V/mm]: 1; Protective bellows: Viton®; Cable orientation: Radial; Cable length [m]: 2.2; Series: GT622; Maximum permissible error for linearity deviations [µm]: 1 + 4 x L.
Key features
- Measuring range: ± 5 mm
- Repeatability limit: 0.1 µm
- Hysteresis: 0.15 µm
- Measuring force: 2 N
- Protection rating: IP65
- Mass: 173 g
- Plunger lift: Advance: pressure, lift: spring
Technical data
| Series | GT622 |
| Measuring range [mm] | ± 5 |
| Repeatability limit [µm] | 0.1 |
| Protection rating | IP65 |
| Hysteresis [µm] | 0.15 |
| Maximum permissible error for linearity deviations [µm] | 1 + 4 x L |
| Measuring force [N] | 2 |
| Plunger lift | Advance: pressure, lift: spring |
| Output voltage [V] | ± 5 |
| Sensitivity [V/mm] | 1 |
| Protective bellows | Viton® |
| Cable orientation | Radial; Dimensions |
| Cable length [m] | 2.2 |
| Mass [kg] | 0.173 |
| Mass [g] | 173 |
| Standard | DIN 32876 |
| Material | Mounting shank: nickel-plated; Plunger: hardened steel; Protective bellows: Viton®; Ball contact point: carbide |
| Power supply | Stabilised supply voltage: ± 15 V; Consumption: 15 mAh; Control load: > 1 kΩ; Output voltage: ± 5 V |
| Dimensions | Mounting shank: Ø 8 mm; Contact point thread: M2.5; Ball contact point: Ø 3 mm; Cable: 2 m; Connector: 5-pin DIN 45322 |
| Mass | Moving mass: 8 g |
| Coefficient of linear expansion | 0.2 µm/°C |
| Repeatability | 0.1 µm |
| Measuring range | ± 5 mm |
| Plunger travel | 10.3 mm |
| Rest position | Factory setting: -5 mm; Not adjustable: lower: -5.1 mm, upper: +5.2 mm |
| Working temperature | 20 °C ± 0.5 |
| Sensitivity | 1 V/mm |
| Maximum permissible error for linearity deviations | L in mm; 1 + 4 x L µm |
Supplied with
Probe · Adjustment key · Inspection report · Instruction manual · Declaration of conformity
Official manufacturer product page: tesatechnology.com
Price and availability
Products without a listed price are offered in a configuration defined together with our technical support: contact us for a quote stating the model, quantity and application.
Selection guide: GT 622 DC pneumatic probe 5 mm 2 N TESA
TESA GT622 DC probe, pneumatic, ± 5 mm, force = 2 N, radial cable – measuring range ± 5 mm; repeatability limit 0.1 µm; hysteresis 0.15 µm.
TESA inductive probes (half-bridge system) are selected according to measuring range (± 1, ± 2, ± 5 mm), measuring force (from 0.16 to 4 N depending on the material and finish of the workpiece), cable exit (axial or radial, depending on the space available in the fixture) and plunger lift (manual or pneumatic, GTx2 and GTLx2 versions). The GTL versions are linearised for maximum accuracy over the whole range; the DC versions have a voltage analogue output for PLCs; the USB versions connect directly to a PC without a display unit; the FMS parallel-guided probes are for measurements with constant force and interchangeable probes; lever probes are for hard-to-reach points. The probe must be paired with a display unit (TWIN, TT100) or an interface (M4P-3, TESA-MODUL) and with suitable contact points.
If in doubt, contact us: our technical support will advise you on the right model, measuring force, contact points and display unit for your application.
Integration and programming
The probe is fixed by its Ø 8 mm h6 shank in the holder or measuring fixture and connected to the display unit or interface via the 5-pin DIN connector (or USB for the USB versions, voltage output for the DC versions). Zeroing, presets, tolerances and formulas between several probes are set on the display unit; with M4P-3 and TESA-MODUL the signals go to PLCs, acquisition boards and SPC software. Probes with pneumatic plunger lift require the pneumatic accessories (electropneumatic pump, fittings) listed among the accessories.
Calibration and repair
Every TESA probe is supplied with an inspection report and a declaration of conformity. Periodic verification on gauge blocks or setting standards is recommended and, for quality systems, calibration with a traceable certificate; replace worn contact points and damaged bellows. After impacts or unstable readings the probe should be sent in for service.
Service: RODER S.r.l. – INNOVACHECK division handles verification, calibration with certificate and repairs of TESA probes and display units in Italy. Contact us stating the model and serial number.